How to secure international sourcing

List of the table of contents of this article:

• 1, How to use the glass lifting switch of the car
• 2 、How to raise and lower the car window
• 3, What's wrong with the car window that can't be raised and lowered automatically?
• 4, Car glass lifting and tightening solution

How to use the glass lifting switch of the car

Rear window locking switch: When this switch is pressed, the left and right rear windows and the co-driver window adjustment switches can be disabled. At this time, only the main driver's door can be opened. The closing button can adjust the window. Window switch: The window can be raised and lowered by pressing and pulling up the switch.

First, make sure that the vehicle is parked and turn off the engine. Open the front door of the driver's side of the vehicle, pull open the front seat, find a face-up Rockerswitch button, and then click it to realize the function of raising and lowering the window.

How to raise and lower the car window 1 When using ordinary electric windows, you need to press and hold the switch. When the window is raised to the required position, release the button, and the lifting process will stop.There are two gears of the window lifting control switch of the car equipped with one-button window lifting, and the position of the first button is the same as that of ordinary electric windows.

The operation method of the car window is to drop with one button, press the switch completely and release it. One-button rise, fully lift the switch and release, press or lift the switch again, and the window will stop moving. If you don't support one-click lifting, you need to press or lift it all the time. If there is a child in the back seat, you can press the rear window lock function.

First, pull up the switch until the window is completely closed, and continue to pull up the switch for 2 seconds and release it. Press down the switch to lower the window from the top to the bottom, and continue to press the switch for 2 seconds and release it. After completing these two steps, the window self-learning is successful, and the window one-click lifting and anti-pinch function are restored.

How to raise and lower the car window

1. The lifting of the window is controlled by the electric motor, and the lifting operation methods include the following manual operations: the window lifting button is generally located on the inside of the door, and the lifting button can be pressed by one hand to achieve the rise or fall.

2. First, make sure that the vehicle is parked and turn off the engine. Open the front door of the driver's side of the vehicle, pull open the front seat, find a face-up Rockerswitch button, and then click it to realize the function of raising and lowering the window.

3. How to raise and lower the car window 1 When using ordinary electric windows, you need to hold down the switch. When the window is raised to the required position, release the button, and the lifting process will stop. There are two gears of the window lifting control switch of the car equipped with one-button window lifting, and the position of the first button is the same as that of ordinary electric windows.

What's wrong with the car window that can't be raised and lowered automatically?

The specific reasons why the car window cannot be raised and lowered are analyzed as follows: the window lifting motor is damaged or the electronic control harness is in poor contact: if there is a burning smell or abnormal sound in the door panel when the window opening button is pressed for a long time, it is likely to be the window.If the lifting motor parts are damaged, it is recommended to go directly to a 4s store or auto repair shop to replace the glass lifting motor.

Damage to the window lifting motor or poor contact with the electronic control harness; overheating protection of the motor; blockage of the guide rail or aging of the adhesive strip; damage to the switch of the glass lifter; deviation of the installation position of the guide rail, etc. may cause the inability to raise and lower the window of the car.

The window lifting motor is damaged or the electronic control harness is in poor contact. If there is a burning smell or there is a strange sound in the door panel when the window opening button is pressed for a long time, it is very likely that the window lifting motor parts are damaged. In this case, it is recommended to directly find a 4S store or auto repair shop to replace the glass lifting motor.

Car glass lifting and tightening solution

1. When lifting the glass, it is found that there is a stuttering and not smooth.Lower the glass to a minimum and spray the panel wax into the adhesive strips on both sides of the glass. The glass was raised and lowered several times, and it was found that the phenomenon of stuttering and not smoothness was weakened. The glass is lowered to a minimum again, and the panel wax is sprayed into the adhesive strips on both sides of the glass.

2. The fastest way to solve the difficulty of raising and lowering the window: turn on the ignition switch, pull the switch up and save it. After the glass rises to the top, continue to pull the switch for more than 3 seconds, release the switch and hold it immediately until the glass drops to the bottom for more than 3 seconds, repeat the lifting action again, and the initialization program is completed. The window lifting function is restored.

3. To remove the dirt in the glass guide groove, the tools used are very simple: a chopstick, a small towel, a basin of water, wet the towel and wring it. Wrap it to the end of the chopsticks to set up a cleaning tool. If the towel is dirty, take it down and clean it, and then wrap it up for further use.

4. Cause analysis: looseness of screws or snaps; foreign objects in the door trim panel; there is a gap between the glass and the inner pressure strip. To solve this kind of small problem, you only need to clean up foreign objects, fasten the glass, fix the screws or replace the internal pressure strip in time. Specific coping methods: (1) Caused by loose screws/clatches.

5. The parts that may fail in the glass lifter include wires, sliders, etc. The only solution is to replace the glass lifter. When the glass lifting guide rail is dirty, it will also play a certain resistance to the lifting of the glass. The solution is to clean the glass lifting guide rail and apply lubricant at the same time.

6. The solution to the hard work of lifting and lowering car glass: to remove the dirt in the glass guide groove. The tools used are very simple: a chopstick and a small towel., a basin of water, wet the towel and wist it, wrap it to the end of the chopsticks to make a cleaning tool. If the towel is dirty, take it off and clean it, and then wrap it to continue to use it.