The working principle of the water level switch, the capacitive water level switch uses a special ADA capacitance detection chip for signal processing according to the change of the small capacitance difference caused by detecting the change of the water level, and can output a variety of signal communication protocols.
Sound fork liquid level switch ● Working principle: Sound fork liquid level switch is a new type of liquid level switch. It is designed and made using the principle of tuning fork vibration.
The principle of water level switch The water level switch is also known as water level pressure switch, water level sensor and water level controller. It uses the pressure generated by the high and low tide of the water level in the laundry bucket to control the on-off of the contact switch. The structure is shown in the figure below. The water level switch is connected to the gas chamber mouth on the lower side of the water bucket with a plastic hose.
The working principle of the tuning fork liquid level switch is to make the tuning fork vibration at a certain resonance frequency through a pair of piezoelectric crystals installed on the base.
It has the following characteristics: clear water level display, bright color, large observation angle, and long visual distance. It is suitable for all kinds of medium and low pressure boilers, which are not affected by water quality, with stable performance and long service life.The water level can be displayed from a distance to any position. High and low water level sound and light alarm.
The water level meter adopts a diode cold light source, which has good viewing effect, adjustable brightness, long life, easy maintenance, low energy consumption, and a wide viewing range. After the water level meter is installed, the light source basically does not need to be adjusted, and you can see gas red and liquid green. The ruler has a light source, which is conducive to night viewing. If a water level meter is installed for monitoring, there is no need to add another lighting source to the scene.
The two-color water level meter is reliable to use and the display is intuitive. It can be connected to the central control room through the camera, which is an ideal boiler water level meter. However, you should pay attention to regular flushing, and some manufacturers' product bulbs have a short life and need to be replaced frequently. Magnetic flip plate level meter. It is also a vertical pipe.
Make the gas phase red and the liquid phase green. Nowadays, many manufacturers call liquid level meters that can identify liquid levels in different colors as two-color liquid level meters.In fact, the former refers to a measurement principle, and the latter refers to a display form. The former has good performance under high temperature and high pressure, while the latter has advantages in cost and scope of application.
1. Conductive detection principle The principle of conductive water level sensor is to use the conductivity of water to detect the height of the water surface, and use resistance connections for switch control. The principle of float detection The principle of float is to detect the height of the water surface through the interruption of the reed at different heights.
2, conductive water level water temperature sensor (probe): There is also a temperature probe in the middle of the sensor. At present, more than 50% of the sensors of solar water heaters are conductive sensors, which has the advantages of low cost and easy installation; the biggest disadvantage is that it is greatly affected by the quality of water, is easy to scale, and has a service life of about one year.
3. The water level sensor in the solar water heater transmits the perceived water level signal to the controller. The computer in the controller compares the actual measured water level signal with the set signal to obtain the deviation. Then, according to the nature of the deviation, it sends a switch instruction to the water supply electric valve to ensure solar thermal The water level reaches the set water level.
1. The basic working principle of the closed-loop control system is as follows: (1) Detect the actual value of the controlled amount or output quantity;(2) Compare the actual value with the given value to obtain the deviation value; (3) Use the deviation value to produce control and adjustment effects to eliminate the deviation. This kind of system based on the feedback principle, which corrects the deviation by detecting the deviation, is called a closed-loop control system.
2. Control according to the information of changes in the system output, that is, by comparing the deviation between the system behavior (output) and the expected behavior, and eliminating the deviation to obtain the expected system performance.
3. Most of the controls implemented in management are closed-loop control, and the control principle used is mainly the feedback principle.
4. The basic principle is the same as the steel belt level meter, but it has an accurate force sensor and servo system to form a closed-loop adjustment system. By considering the gravity of the steel belt itself, the height of the float is accurately adjusted to balance buoyancy and gravity, and the current liquid level to the top of the tank is obtained to obtain the liquid level value.
5. The so-called feedback principle is to control according to the information of the system output changes, that is, to obtain the expected system performance by comparing the deviation between the system behavior (output) and the desired behavior and eliminating the deviation.
1. First of all, the zero point of the double chamber equilibrium level meter needs to ensure that the positive and negative pressure chamber is filled with condensate. Secondly, close the balance valve and open the positive and negative phase valves. Finally, close the vapor-liquid phase valve of the double chamber balance container at the same time.
2. I) There are 2 adjustable bottom corners (2 in the front row) at the bottom. When you find that the refrigerator is unflat or shaking, adjust the bottom foot to level the refrigerator. Rotating the bottom foot clockwise can raise the refrigerator, and rotating the bottom foot counterclockwise can lower the refrigerator.
3. In addition, if you are sure that the height of your B water tank needs to reach is H, then you just need to put your inlet pipe position a few centimeters higher than the height of the B water tank H.
4. The real dual water tank system is to divide the two water tanks into solar energy sets.Hot water tank (specialized in absorbing and storing solar energy) and hot water supply tank (water tank constant temperature control, water tank temperature directly controls the start and stop of the auxiliary heat source), this system is energy-saving and safe.
5. First of all, close the balance gate under the premise of ensuring that the positive and negative pressure chamber of the single-chamber balance container is filled with condensate. Secondly, open the positive and negative phase gate. Finally, open the gas-liquid phase valve of the double-chanter balance container to complete the debugging.
6. Thermostat knob adjustment method: The refrigerator temperature controller knob generally has 0 and 7 gears. The larger the number, the lower the temperature in the freezer. Generally, we put it in the 3rd gear in spring and autumn. It depends on your requirements and whether the freezer can reach below minus 18 degrees.
1. The single-capacitance liquid level control system has only one storage tank, so there is no lag effect, the response speed is faster, and it is easier to achieve stable control.
2. The integral effect is enhanced. The enhancement of the integral effect makes the system unstable and becomes a second-order system, and the output may oscillate, which makes the dual-capacitance liquid level control system more difficult to stabilize than the single-capacity liquid level control system. The proportion should be increased while the integral action is enhanced.
3. Because the double volume is equivalent to the series of two single volumes, it becomes a second-order system, and the output may oscillate. The single volume is a first-order system, and the output is exponentially monotonically converged.
4. The coolant used in different regions is also different. AppearAll cars use special coolant, and pure water can be used in a short-term emergency, but you have to go to a professional car repair shop to repair the cooling system immediately, then clean the cooling system, and then add a new coolant. The coolant can be replaced with a cycle of two years or 20,000 kilometers.
5. More energy-saving. The double-capacity water tank is a very cost-effective refrigerator. The purpose of liquid level control is to be more energy-saving and more power-saving.
Customizable export data queries-APP, download it now, new users will receive a novice gift pack.
The working principle of the water level switch, the capacitive water level switch uses a special ADA capacitance detection chip for signal processing according to the change of the small capacitance difference caused by detecting the change of the water level, and can output a variety of signal communication protocols.
Sound fork liquid level switch ● Working principle: Sound fork liquid level switch is a new type of liquid level switch. It is designed and made using the principle of tuning fork vibration.
The principle of water level switch The water level switch is also known as water level pressure switch, water level sensor and water level controller. It uses the pressure generated by the high and low tide of the water level in the laundry bucket to control the on-off of the contact switch. The structure is shown in the figure below. The water level switch is connected to the gas chamber mouth on the lower side of the water bucket with a plastic hose.
The working principle of the tuning fork liquid level switch is to make the tuning fork vibration at a certain resonance frequency through a pair of piezoelectric crystals installed on the base.
It has the following characteristics: clear water level display, bright color, large observation angle, and long visual distance. It is suitable for all kinds of medium and low pressure boilers, which are not affected by water quality, with stable performance and long service life.The water level can be displayed from a distance to any position. High and low water level sound and light alarm.
The water level meter adopts a diode cold light source, which has good viewing effect, adjustable brightness, long life, easy maintenance, low energy consumption, and a wide viewing range. After the water level meter is installed, the light source basically does not need to be adjusted, and you can see gas red and liquid green. The ruler has a light source, which is conducive to night viewing. If a water level meter is installed for monitoring, there is no need to add another lighting source to the scene.
The two-color water level meter is reliable to use and the display is intuitive. It can be connected to the central control room through the camera, which is an ideal boiler water level meter. However, you should pay attention to regular flushing, and some manufacturers' product bulbs have a short life and need to be replaced frequently. Magnetic flip plate level meter. It is also a vertical pipe.
Make the gas phase red and the liquid phase green. Nowadays, many manufacturers call liquid level meters that can identify liquid levels in different colors as two-color liquid level meters.In fact, the former refers to a measurement principle, and the latter refers to a display form. The former has good performance under high temperature and high pressure, while the latter has advantages in cost and scope of application.
1. Conductive detection principle The principle of conductive water level sensor is to use the conductivity of water to detect the height of the water surface, and use resistance connections for switch control. The principle of float detection The principle of float is to detect the height of the water surface through the interruption of the reed at different heights.
2, conductive water level water temperature sensor (probe): There is also a temperature probe in the middle of the sensor. At present, more than 50% of the sensors of solar water heaters are conductive sensors, which has the advantages of low cost and easy installation; the biggest disadvantage is that it is greatly affected by the quality of water, is easy to scale, and has a service life of about one year.
3. The water level sensor in the solar water heater transmits the perceived water level signal to the controller. The computer in the controller compares the actual measured water level signal with the set signal to obtain the deviation. Then, according to the nature of the deviation, it sends a switch instruction to the water supply electric valve to ensure solar thermal The water level reaches the set water level.
1. The basic working principle of the closed-loop control system is as follows: (1) Detect the actual value of the controlled amount or output quantity;(2) Compare the actual value with the given value to obtain the deviation value; (3) Use the deviation value to produce control and adjustment effects to eliminate the deviation. This kind of system based on the feedback principle, which corrects the deviation by detecting the deviation, is called a closed-loop control system.
2. Control according to the information of changes in the system output, that is, by comparing the deviation between the system behavior (output) and the expected behavior, and eliminating the deviation to obtain the expected system performance.
3. Most of the controls implemented in management are closed-loop control, and the control principle used is mainly the feedback principle.
4. The basic principle is the same as the steel belt level meter, but it has an accurate force sensor and servo system to form a closed-loop adjustment system. By considering the gravity of the steel belt itself, the height of the float is accurately adjusted to balance buoyancy and gravity, and the current liquid level to the top of the tank is obtained to obtain the liquid level value.
5. The so-called feedback principle is to control according to the information of the system output changes, that is, to obtain the expected system performance by comparing the deviation between the system behavior (output) and the desired behavior and eliminating the deviation.
1. First of all, the zero point of the double chamber equilibrium level meter needs to ensure that the positive and negative pressure chamber is filled with condensate. Secondly, close the balance valve and open the positive and negative phase valves. Finally, close the vapor-liquid phase valve of the double chamber balance container at the same time.
2. I) There are 2 adjustable bottom corners (2 in the front row) at the bottom. When you find that the refrigerator is unflat or shaking, adjust the bottom foot to level the refrigerator. Rotating the bottom foot clockwise can raise the refrigerator, and rotating the bottom foot counterclockwise can lower the refrigerator.
3. In addition, if you are sure that the height of your B water tank needs to reach is H, then you just need to put your inlet pipe position a few centimeters higher than the height of the B water tank H.
4. The real dual water tank system is to divide the two water tanks into solar energy sets.Hot water tank (specialized in absorbing and storing solar energy) and hot water supply tank (water tank constant temperature control, water tank temperature directly controls the start and stop of the auxiliary heat source), this system is energy-saving and safe.
5. First of all, close the balance gate under the premise of ensuring that the positive and negative pressure chamber of the single-chamber balance container is filled with condensate. Secondly, open the positive and negative phase gate. Finally, open the gas-liquid phase valve of the double-chanter balance container to complete the debugging.
6. Thermostat knob adjustment method: The refrigerator temperature controller knob generally has 0 and 7 gears. The larger the number, the lower the temperature in the freezer. Generally, we put it in the 3rd gear in spring and autumn. It depends on your requirements and whether the freezer can reach below minus 18 degrees.
1. The single-capacitance liquid level control system has only one storage tank, so there is no lag effect, the response speed is faster, and it is easier to achieve stable control.
2. The integral effect is enhanced. The enhancement of the integral effect makes the system unstable and becomes a second-order system, and the output may oscillate, which makes the dual-capacitance liquid level control system more difficult to stabilize than the single-capacity liquid level control system. The proportion should be increased while the integral action is enhanced.
3. Because the double volume is equivalent to the series of two single volumes, it becomes a second-order system, and the output may oscillate. The single volume is a first-order system, and the output is exponentially monotonically converged.
4. The coolant used in different regions is also different. AppearAll cars use special coolant, and pure water can be used in a short-term emergency, but you have to go to a professional car repair shop to repair the cooling system immediately, then clean the cooling system, and then add a new coolant. The coolant can be replaced with a cycle of two years or 20,000 kilometers.
5. More energy-saving. The double-capacity water tank is a very cost-effective refrigerator. The purpose of liquid level control is to be more energy-saving and more power-saving.
HS code-based competitor benchmarking
author: 2024-12-24 00:58Real-time import export alerts
author: 2024-12-24 00:30Understanding HS codes in trade data
author: 2024-12-24 00:22How to reduce shipping delays with data
author: 2024-12-24 00:07HS code alignment with trade strategies
author: 2024-12-24 02:17HS code integration with supply chain
author: 2024-12-24 01:20Trade data-based price benchmarks
author: 2024-12-24 01:02
Sustainable supply chain analytics
821.54MB
Check
Container-level shipment data
615.34MB
Check
Trade data for FMCG sector
373.59MB
Check
HS code integration with digital customs forms
865.75MB
Check
HS code research for EU markets
984.73MB
Check
Exotic wood imports HS code references
696.45MB
Check
How to understand re-export regulations
766.29MB
Check
Trade data-driven portfolio management
717.54MB
Check
Locating specialized suppliers by HS code
345.24MB
Check
Trade data-driven policy analysis
131.78MB
Check
HS code-driven portfolio diversification
277.72MB
Check
Global trade supply chain modeling
869.16MB
Check
HS code-based trade route profitability
424.89MB
Check
How to ensure transparency in supply chains
718.84MB
Check
CIS countries HS code usage patterns
288.13MB
Check
HS code monitoring tools for exporters
571.69MB
Check
Fisheries products HS code classification
638.57MB
Check
Industrial equipment HS code alignment
329.72MB
Check
HS code alignment with import quotas
133.14MB
Check
HS code-based customs broker selection
738.89MB
Check
HS code-driven compliance workflows
824.37MB
Check
Real-time customs tariff analysis
149.17MB
Check
Global trade contract verification
826.87MB
Check
Trade data for food and beverage industry
394.87MB
Check
Real-time container throughput data
334.36MB
Check
Petroleum products HS code insights
125.41MB
Check
Top trade data plugins for analytics
933.29MB
Check
Sustainable supply chain analytics
311.41MB
Check
How to comply with EU trade regulations
795.58MB
Check
Global trade alerts and updates
959.79MB
Check
Pharma cold chain HS code analysis
174.67MB
Check
Cross-border HS code harmonization
656.35MB
Check
Best trade data solutions for startups
135.94MB
Check
Global trade data harmonization
642.49MB
Check
Ship parts HS code verification
487.15MB
Check
Global trade compliance automation suites
355.48MB
Check
Scan to install
Customizable export data queries to discover more
Netizen comments More
1132 Dairy imports HS code references
2024-12-24 01:50 recommend
2998 Cross-border HS code harmonization
2024-12-24 01:37 recommend
2933 Industrial gases HS code verification
2024-12-24 01:36 recommend
2461 HS code harmonization in NAFTA region
2024-12-24 00:24 recommend
2162 Medical diagnostics HS code classification
2024-12-24 00:18 recommend