1. After all the wiring connections of the anti-theft device host are completed, the decorative board should be debugged before installing. Check whether each wiring plug is in contact with the host socket and tight, and whether there is any looseness.
2. Installation method and precautions of the anti-theft device x0dx0a preparations x0dx0a tools x0dx0a wire stripping pliers, electric measuring pen (12V-24V), screwdriver (cross, one character), insulating tape, tool knife, double-sided adhesive, tie, and some other disassembly tools ( It depends on the specific model).
3. Wiring requirements: the connector should be tightly connected, avoid virtual connection, and wrap it with insulating tape. This process is the most important step in the whole installation process. If the connection is wrong, the anti-theft device cannot be used in the light, and the components in the car will be burned, making the vehicle unable to use normally or even causing a fire.
Where is the car alarm installed?&Mdash The procedure for installing the anti-theft alarm First check the condition of the car: such as battery voltage, water temperature gauge, oil gauge, headlights, small lights, turn signals, brake lights, indoor lights, airbag lights, ABS lights, SRS, sunroof, etc.
Car anti-theft alarms are generally installed in the dashboard of the cab, mainly equipped with the main control box, vibration sensor and status indicator light. Installation method of car anti-theft device First of all, check whether the lock head, turning light, side door light and engine of the original car are working normally. If everything is normal, you can start installing it.
The installation location requirements of different types of car anti-theft alarms are different: wired car anti-theft alarms can generally be considered to be installed under the dashboard or under the driver's seat. If only the positioning function is installed, roof lights, side doors, taillights and many other places can also be considered.
The steps for installing the car anti-theft device are as follows: In the connection of the circuit breaker, you must first confirm the ignition line, fuel pump control line and start line before choosing which route to disconnect, (there is no anti-robb function when disconnecting the start line); the anti-theft host input ON line should be docked to the upper end of the disconnection circuit.
Notes: 1) The installation of the anti-theft lock should be in place. It is best to keep the lock core parallel to the body floor, and the closer it is to the fixture in the car, the better. 2) Use anti-theft alarm and car anti-theft lock at the same time to prevent theft, which has a better anti-theft effect. 3) If the anti-theft system fails, don't disassemble it by yourself. You should go to a professional repair shop to deal with it.
1. The steps to install the car anti-theft device are as follows: power offIn the connection of the device, you must first confirm the ignition line, fuel pump control line and start line before choosing which route to disconnect, (there is no anti-robb function when disconnecting the start line); the anti-theft host input ON line should be docked at the upper end of the disconnection circuit.
2. Confirm whether the original car has a central control lock before installation. If so: judge what kind of trigger form it is. When installing the anti-theft device, you can wire it according to the "central control lock wiring diagram" in the "installation circuit diagram".
3. Before installing the anti-theft alarm, check the original car circuit: start the circuit: turn the car key to the ON position and observe the lighting of each indicator light (such as airbag, ABS, charging, engine fault light, etc.) in the dashboard.), then start the vehicle normally, and then observe whether each indicator light Abnormally extinguished.
The car anti-theft alarm is generally installed in the dashboard of the cab, mainly installing the main control box, vibration sensor and status indicator light. Installation method of car anti-theft device First of all, check whether the lock head, turning light, side door light and engine of the original car are working normally. If everything is normal, you can start installing it.
Confirm whether the original car has a central control lock before installation. If so: judge what kind of trigger form it is. When installing the anti-theft device, you can wire it according to the "central control lock wiring diagram" in the "installation circuit diagram".
Installation: Find the +12V normal fire line, negative electricity (iron), turn signal line, door edge line, brake line, start motor line, central control line, on/off signal line, etc. to be connected.After checking and installing, you must self-check whether all functions of the vehicle are normal, and then put the removed trim panel back into its original own.
How to install the car burglar alarm? In the connection of the circuit breaker, it is necessary to confirm the ignition line, the fuel pump adjustment line and the starter line, and then choose which way to disconnect (when the starter line is disconnected, there is no anti-robb function); the anti-theft input on the host line should be connected to the upper end of the disconnection circuit. You can also pick up the car separately.
shipment data access-APP, download it now, new users will receive a novice gift pack.
1. After all the wiring connections of the anti-theft device host are completed, the decorative board should be debugged before installing. Check whether each wiring plug is in contact with the host socket and tight, and whether there is any looseness.
2. Installation method and precautions of the anti-theft device x0dx0a preparations x0dx0a tools x0dx0a wire stripping pliers, electric measuring pen (12V-24V), screwdriver (cross, one character), insulating tape, tool knife, double-sided adhesive, tie, and some other disassembly tools ( It depends on the specific model).
3. Wiring requirements: the connector should be tightly connected, avoid virtual connection, and wrap it with insulating tape. This process is the most important step in the whole installation process. If the connection is wrong, the anti-theft device cannot be used in the light, and the components in the car will be burned, making the vehicle unable to use normally or even causing a fire.
Where is the car alarm installed?&Mdash The procedure for installing the anti-theft alarm First check the condition of the car: such as battery voltage, water temperature gauge, oil gauge, headlights, small lights, turn signals, brake lights, indoor lights, airbag lights, ABS lights, SRS, sunroof, etc.
Car anti-theft alarms are generally installed in the dashboard of the cab, mainly equipped with the main control box, vibration sensor and status indicator light. Installation method of car anti-theft device First of all, check whether the lock head, turning light, side door light and engine of the original car are working normally. If everything is normal, you can start installing it.
The installation location requirements of different types of car anti-theft alarms are different: wired car anti-theft alarms can generally be considered to be installed under the dashboard or under the driver's seat. If only the positioning function is installed, roof lights, side doors, taillights and many other places can also be considered.
The steps for installing the car anti-theft device are as follows: In the connection of the circuit breaker, you must first confirm the ignition line, fuel pump control line and start line before choosing which route to disconnect, (there is no anti-robb function when disconnecting the start line); the anti-theft host input ON line should be docked to the upper end of the disconnection circuit.
Notes: 1) The installation of the anti-theft lock should be in place. It is best to keep the lock core parallel to the body floor, and the closer it is to the fixture in the car, the better. 2) Use anti-theft alarm and car anti-theft lock at the same time to prevent theft, which has a better anti-theft effect. 3) If the anti-theft system fails, don't disassemble it by yourself. You should go to a professional repair shop to deal with it.
1. The steps to install the car anti-theft device are as follows: power offIn the connection of the device, you must first confirm the ignition line, fuel pump control line and start line before choosing which route to disconnect, (there is no anti-robb function when disconnecting the start line); the anti-theft host input ON line should be docked at the upper end of the disconnection circuit.
2. Confirm whether the original car has a central control lock before installation. If so: judge what kind of trigger form it is. When installing the anti-theft device, you can wire it according to the "central control lock wiring diagram" in the "installation circuit diagram".
3. Before installing the anti-theft alarm, check the original car circuit: start the circuit: turn the car key to the ON position and observe the lighting of each indicator light (such as airbag, ABS, charging, engine fault light, etc.) in the dashboard.), then start the vehicle normally, and then observe whether each indicator light Abnormally extinguished.
The car anti-theft alarm is generally installed in the dashboard of the cab, mainly installing the main control box, vibration sensor and status indicator light. Installation method of car anti-theft device First of all, check whether the lock head, turning light, side door light and engine of the original car are working normally. If everything is normal, you can start installing it.
Confirm whether the original car has a central control lock before installation. If so: judge what kind of trigger form it is. When installing the anti-theft device, you can wire it according to the "central control lock wiring diagram" in the "installation circuit diagram".
Installation: Find the +12V normal fire line, negative electricity (iron), turn signal line, door edge line, brake line, start motor line, central control line, on/off signal line, etc. to be connected.After checking and installing, you must self-check whether all functions of the vehicle are normal, and then put the removed trim panel back into its original own.
How to install the car burglar alarm? In the connection of the circuit breaker, it is necessary to confirm the ignition line, the fuel pump adjustment line and the starter line, and then choose which way to disconnect (when the starter line is disconnected, there is no anti-robb function); the anti-theft input on the host line should be connected to the upper end of the disconnection circuit. You can also pick up the car separately.
Global trade data normalization
author: 2024-12-24 00:10HS code-based landed cost calculations
author: 2024-12-23 23:38HS code-driven import quality checks
author: 2024-12-23 23:32Global supply chain risk assessment
author: 2024-12-23 22:38Global trade tender evaluation tools
author: 2024-12-24 00:42Trade data for regulatory compliance
author: 2024-12-24 00:19How to ensure data-driven export strategies
author: 2024-12-24 00:02Food additives HS code classification
author: 2024-12-23 23:34727.11MB
Check722.28MB
Check312.99MB
Check986.92MB
Check488.63MB
Check923.68MB
Check773.76MB
Check415.16MB
Check622.77MB
Check138.72MB
Check636.86MB
Check336.27MB
Check318.24MB
Check179.52MB
Check469.14MB
Check164.27MB
Check399.45MB
Check778.58MB
Check637.47MB
Check819.12MB
Check641.69MB
Check298.67MB
Check161.51MB
Check552.58MB
Check651.14MB
Check581.92MB
Check299.71MB
Check462.38MB
Check781.89MB
Check664.95MB
Check498.68MB
Check851.51MB
Check354.21MB
Check679.97MB
Check445.48MB
Check631.87MB
CheckScan to install
shipment data access to discover more
Netizen comments More
253 European Union trade analytics
2024-12-24 00:36 recommend
439 West African HS code trade guides
2024-12-23 23:44 recommend
1922 USA importers database access
2024-12-23 23:10 recommend
2157 Customized market entry reports
2024-12-23 22:24 recommend
1185 Textile yarn HS code mapping
2024-12-23 22:07 recommend