How to ensure trade compliance audits

List of contents of this article:

• 1, How to power the car battery
• 2 、< A href='#The How to ensure trade compliance auditscorrect method of car electricity' title='The correct method of car electricity'>The correct method of car electricityLaw
• 3, The correct way to wire car batteries
• 4, How to power a car
• 5, What to do if the car battery runs out of power
• 6, How to light a fire when the car battery is dead

How to power the car battery

1. After the fire, it is recommended to keep the car in the starting state for about 30 minutes, and let the generator fully charge the battery, otherwise it is easy to fail to ignite again.If it is a manual transmission model, in addition to starting it by electric power, you can also ask someone to help you push the car directly.

2. However, you need to master the correct method of power-up, otherwise there will be a danger of power-up failure, inability to start or even burning the batteries of the two cars. The correct way to power a car must be to connect the positive pole and the negative pole to the negative pole, otherwise it will burn the battery, but it is definitely not as simple as the positive pole directly to the positive pole and the negative pole directly to the negative pole.

3. Unplug the cross-connected cable on the vehicle in the opposite order to the connecting cable (unplug the negative pole (the clip connecting the grounded metal) first, and then the positive pole). 1 Let the engine of the car that has just been out of power run at a speed slightly higher than the idle speed for at least 20 minutes to charge the battery.

4. How to charge the car battery? The charging method of the new car battery is to connect the positive pole of the battery to the positive pole of the power supply, and the negative pole of the battery to the negative pole of the power supply. The initial charging is carried out in two stages: first, the initial charging current is charged to the electrolyte to release bubbles, and the single-grid voltage rises to 3-4V.

The correct method of electricity of automobile

The specific operation steps of the correct method of wiring of the car are as follows: connect the positive electrode of the battery of the rescue vehicle with a connecting wire; connect the positive electrode of the battery of the powerless vehicle on the other side; connect the rescue vehicle with another connection wire The negative pole; the remaining end should not be connected to the negative pole of the battery of the powerless vehicle, and the iron parts of the engine body should be connected.

There are two ways to power a car, one is to use other vehicles to power, and the other is to use an external power supply.

The correct way to power the car must be to connect the positive pole and the negative pole to the negative pole, otherwise it will burn the battery, but it is definitely not as simple as the positive pole directly to the positive pole and the negative pole directly to the negative pole. Although the vehicle can be started by directly connecting the batteries of the two cars, it will fail most of the time.

The correct method of wiring the car battery

The correct connection method of the battery wire: connect the positive pole first, and then connect the negative pole. Connect the positive poles of the two cars first, and then connect the negative poles. This order is to prevent accidental short circuit on the iron. Among them, when connecting the negative pole, the negative pole of many cars is blocked by other parts and cannot be connected.

I have met many car owners who don't know how to power their cars, so what is the correct way to power their cars?Let's take a look together. How to charge the car battery: The fronts of the two cars are close to each other, and prepare two charging cables. Open the hood and connect the positive and negative electrodes of the two batteries with a charging cable. Red is connected to the positive pole and black is connected to the negative pole.

The method of connecting the positive and negative poles of the car battery: the positive pole is connected to the main line, and the negative pole is connected to the iron, that is, it is connected to the large shelf of the car. When there is no power-consuming electrical appliance (direct contact) between the positive and negative lines, it will be short-circuited.

Next, let's take a look at the correct way to wire car batteries. First, take out a cable, one end is connected to the positive pole of the battery of the battery of the battery, and the other end is connected to the positive pole of the battery of the charging car.

Then the owner needs to connect one end of the red connection cable to the positive pole of his vehicle and the other end to the positive pole of the other vehicle. It must be firmly connected and there will be no virtual connection.Then find the black connection wire to connect the negative poles of the two vehicles. It also needs to be firmly connected, and there should be no virtual connection.

How to connect the electricity to the car

1. When the car is connected to electricity, you need to use the wire. There are two types of wire: red and black. The red wire is the positive pole wire, and the black wire is the negative wire. First, take out the red (positive pole) wire and connect one of the ends. To the positive pole of your own vehicle battery, and the other end is connected to the positive pole of other vehicle batteries.

2. Use the battery to connect the batteries of the two cars. The positive pole is connected to the positive pole, and the negative pole is connected to the negative pole. When connecting, pay attention not to make a mistake between the positive and negative poles, and the two clips should not touch to avoid fire. Start the rescue vehicle and turn off all electrical equipment of the vehicle.

3. The method of charging is as follows: the front of the two cars are leaning against each other, and prepare two charging cables. Open the hood and connect the positive and negative electrodes of the two batteries with a charging cable. Red is connected to the positive pole and black is connected to the negative pole.

4. The owner first needs to prepare the car wiring, generally red and black wiring, red is the positive pole wiring, and black is the negative pole wiring. Connect the red wire to one end to the junction pole of the positive pole of your vehicle battery, and connect the other end to the junction pole of the rescue vehicle.

What to do if the car battery runs out

1. There are three ways to use a spare battery, connect electricity, and replace the battery . By connecting the power of the spare battery for emergency, the over-consumed battery can reach a normal state. Connect electricity directly through other vehicles, so that the vehicle with power loss can be restarted.

2. The solution to the problem of the car's power is: start with electricity between cars; start after using a special charger; start the vehicle with the help of downhill; start after replacing the battery by yourself.

3. How to solve the failure of the car battery? Call the insurance company. Generally,It is said that calling the insurance company is the most economical option, because usually when purchasing car damage insurance, you can enjoy the free road rescue services provided by insurance companies, including problems such as battery failure or flat tires.

4. What to do if the car battery runs out of power? The vehicle battery runs out of power. There are the following solutions: the first method is to start the cart. This method is only applicable to manual transmission cars. The battery is preferably a little charged, and the terrain meets the conditions. The second way is to borrow electricity.

5. If the car battery is out of power and cannot be ignited, three methods can be used: the first can be used to start the cart emergency, of course, this is only for manual transmission models; the second is to borrow the car wiring and bridge to start; the third is to use a mobile emergency power bank to charge and start.

6. What to do if the car runs out of powerStart If the car is out of power, you can find an electric rescue vehicle and use the starter lever. If both methods are not feasible, then the battery needs to be replaced. When the car is out of power, timely measures should be taken to avoid damage to the vehicle.

How to set fire when the car battery is out of power

Wiling and bridge method. This method requires another vehicle with a normal battery. Prepare two battery wires and distinguish the positive and negative poles. Connect one battery cable to the positive end of the two car batteries, and the other one to the negative end. After the power is completed and you wait for more than ten minutes, you can try to ignition.

If the car battery is out of power, you can use a cart to help start, build a wire to assist in starting, and use the car emergency power supply to start.This is the easiest way to start the human cart. I believe everyone has seen it in real life. That is, the owner of the car is sitting in the car and driving, and someone is pushing the car behind the car.

The method of starting and ignition when the car battery is out of power is as follows: cart start-up method. This is the most familiar and effective emergency method, but it is better not to use this method unless it is a last resort, because it has certain damage to the engine and clutch of the car.