HS code-based forecasting for exports

List of catalogs of this article:

• 1, What is the function of the car ignition line
• 2. Some details that are easy to be overlooked during car maintenance
• 3、Three lines of the ignition coil What is the line
• 4, How to connect the car ignition switch line
• 5, The 1234 lines on the Skoda Mingrui igniter are What is it used for

What is the function of the car ignition line

The function of the car igniter is to start the engine.An igniter refers to a device that can provide enough energy in an instant to ignite coal powder, oil (gas) fuel and stabilize the flame. The car igniter is a system for starting the engine of a vehicle.

What is the function of the ignition coil? Introduction to the ignition coil, as the name implies, is the most critical part of the engine's work to supply power to the ignition step and ignite the compressed mixed fuel.

The ignition coil is actually a transformer (including primary windings, secondary windings, iron cores, insulating materials, etc.), which converts the voltage of 12 volts of the car into a voltage of 20,000-30,000 volts. The ignition system of the car uses this high-voltage electricity to ignite the mixed gas in the gas cylinder.

Hello! The ignition line is also called the high-voltage line! It is used to transmit high-voltage electricity, and the material is relatively special! [ If there is a problem with the car, ask the car master. 4S store professional technician, 10 minutes to solve.

The function of the ignition coil is to convert the 12V low-voltage current of the power supply into 15~20kV high-voltage current. The core components of the ignition device are the ignition coil and switch device. To improve the energy of the ignition coil, the spark plug can produce enough energy sparks, which is the basic condition for the ignition device to adapt to the operation of modern engines.

Some details that are easy to be overlooked during car maintenance

1. The first one is car tires. Nowadays, cars are very common. The leather is made of metal, but the tires are rubber products. After experiencing wind and rain, sun and rain, and temperature differences, they are easy to age.

2. Some details that are easy to be overlooked in car maintenanceExhaust pipe The exhaust pipe of the car mainly plays the role of damping vibration and noise reduction and prolonging the life of the exhaust silencer system.

3. The air conditioner filter should be cleaned up in time. After summer, we use air conditioners more frequently. The place of air conditioner filter is the easiest place for everyone to ignore. Don't wait until the air conditioner filter is particularly dirty to clean it up, otherwise some dirty things such as impurities enter the interior of the car, which is not just a problem of the filter.

4. Let's take a look at which places are most easily ignored. Check the ignition coil. Spark plugs are automobile consumables and need regular maintenance and replacement. The ignition coil is the same. As one of the indispensable accessories in the ignition system, it will age or even be damaged in a high temperature and vibration environment for a long time.

What are the three wires of the ignition coil

1. The three wires of the ignition coil are the power cord, the control signal line and the ground wire respectively. The core components of the ignition device are the ignition coil and switch device. To improve the energy of the ignition coil, the spark plug can produce enough energy sparks, which is the basic condition for the ignition device to adapt to the operation of modern engines.

2. The three wires of the ignition coil are the power cord, the control signal line and the ground wire.The core components of the ignition device are the ignition coil and switch device. If the energy of the ignition coil is increased, the spark plug can produce enough energy, which is the basic condition for the ignition device to adapt to the operation of modern engines.

3. The three wires of the ignition coil are the power line, the wiring and the control signal line. The power cord is the internal control of the ignition switch, wiring and engine ECU. First, the control signal ECU computer circuit board output switch signal and control the ignition signal. Among them, the power cord and the iron wire, one is the primary wire, the other is the secondary wire, the two are the fire wire, and the spark plug is the rear iron.

4. The three lines on the Civic ignition coil are the signal point, the power cord and the ground wire. There is no specific replacement cycle for the Civic ignition coil. The ignition coil is one of the parts of the car igniter. The ignition coil can continue to be used without damage, and it needs to be tested when the vehicle's mileage reaches 100,000 kilometers.

5. The three wires of Kaiyue ignition coil are power cable, iron cable and control signal cable respectively. There is no specific replacement cycle for the ignition coil. The ignition coil is one of the components of the car igniter. The ignition coil can continue to be used without damage. It needs to be tested when the vehicle mileage reaches 100,000 kilometers.

How to connect the car ignition switch line

1. Special line: Electrical appliances that need to be connected regardless of the engine operation, such as the receiver and distributor cigarette lighter, etc., are set separately by the ignition switch to supply power. Start the control line: start the control switch (touch disk) of the main circuit and use the magnetic switch to turn on and off.

2. When the ignition switch is in the "OFF" position. Turn the key toWhen the "OFF" position is "OFF", the internal two contacts of its horizontal position are connected, that is, the external wire "black and white line" and "green line" are connected.

3. Car ignition switch structure: (1) The key is started routinely. If the ignition button of one-click start, it only includes functions such as tuning memory (2) One-click start: the button or knob of one-click start must be started when it accepts the existence of the smart key. This induction distance is generally in About 50 centimeters.

4. Hello. What kind of car do you need to see in these six lines? Under normal circumstances. You can follow the switch on the old car. What are the functions and how many gears are there? You can measure it first. Then pick up the new one. Different car models have different connection methods of wires. I hope it can help you and adopt it. Thank you.

5. The first is the battery to the ammeter or directly to the ignition switch called the fire wire.The second is the wire of the first gear of the ignition switch. When the stop is turned off, the first gear is to control the radio. There is no main relay for Pusang cars, and there is only one X-electric relay for cars.

What are the 1234 lines on the Skoda Mingrui igniter used for

1. The functions of the 1234 lines on the Skoda Mingrui igniter are triggering lines and ignition coils respectively. , high-voltage package output line, extinguishing line, and the fifth line ground wire. An igniter refers to a device that can provide enough energy to ignite coal powder, oil (gas) fuel in an instant and stabilize the flame.

2. The functions of the 1234 wires on the Skoda Mingrui igniter are the trigger line, the ignition coil input line, the high-voltage package output line, the extinguishing line, and the fifth line ground wire.

3. The Mingrui igniter is charged. The igniter is mainly composed of power supply, ignition coil, distributor, ignition switch, spark plug, additional resistor and its short circuit device, high and low voltage wire, etc. A car igniter is a system used to start a car engine.

4. Mingrui igniter is electric. The ignition device is mainly composed of power supply, ignition coil, distributor, ignition switch, spark plug, additional resistor and its short-circuit device, high and low voltage wire, etc. The car igniter is a system for starting the engine of a vehicle.