Trade compliance training resources

List of the table of contents of this article:

• 1,Trade compliance training resources What should I do if there is an error when installing the system and the restoration cannot continue
• 2, What to do if the computer fails to restore with one click
• 3, win7 system restore change Failed reinstall system tutorial
• 4. Computer Reinstall System Failure Solution

An error occurs when installing the system, what should I do if the restore can't continue

1. It doesn't matter if the next step is installed. The only impact on the system is that one more user has been established, and the input method is restored to the factory settings. If a blue screen occurs in the process of entering the desktop after installation, you can restart and press F8 to log in to the safe mode. After successfully logging in to the safe mode, you can restart to enter the system.

2. SolutionFirst: After the above problem occurs, directly unplug the USB flash drive and plug it into another computer, delete the efi folder and bootmgr.efi file in the USB flash drive, and the problem will be solved. Then, use this USB flash drive boot disk to install the system, and this problem will not occur.

3. An error occurred when installing the system. The restoration cannot continue is caused by a setting error. The solution is: select Restore to C disk when restoring. Then start to restore, and then click Restart, and the installation will be automatic.

What to do if the computer fails to restore with one click

1. There is a problem with the restored system disk. There is something wrong with the restored system disk, such as broken Wait, you can try to replace the system disk or use other restoration methods.

2. The NOVO key is a one-click recovery key. There is a very small button on the side of the computer, next to which is marked - "a counterclockwise arrow". This is the NOVO button. The function is: in the shutdown state, press this button to start the Lenovo one-click recovery system or BIOS, set the program, or enter the startup menu.

3. widos7 uses CD-ROM to install with one click according to the prompts. You can also use a USB flash drive with boot items to install.Question 4: What should I do if the computer fails to reset and can't be turned on? Fault phenomenon 1: After turning on the power and pressing the power button, the computer does not move.

4. There are many reasons for the failure of reinstalling the system. It may be that your reinstallation method is wrong. You can make a USB boot disk to reinstall the system. The specific steps are as follows: Take Dell notebook as an example. Start the computer and press F12 to enter the BIOS settings and select the BOOT option in the red box, as shown in the figure below. Second, then select the CD-ROM in the red box.

win7 system restore change failure reinstall system tutorial

control panel/system and security/Windows Update (left) change settings/update the important below The option should be changed to never check for updates (Win78).The computer can't be turned on and keeps showing "Configuration failed, restore changes, please do not turn off the computer" update system file error. See if you can enter the safe mode.

Download WIN7 system. Download a WIN7 system to a USB flash drive on the Internet. Generally, it is an ISO format file with a size of about 4G.

It should be recommended to reinstall the system when the system fails. The following are the detailed steps to reinstall the system.

Computer reinstall system failure solution

solution: restore the state before the hardware change and check whether the system can start normally. The failure of the motherboard is mainly due to a problem with the hard disk controller on the motherboard, resulting in unstable data transmission and too high error rate, which will lead to the inability to turn on.

If you encounter someone who installs the abnormal system, you must be familiar with such an interface. What I'm saying is to press the three keys (Ctrl+Alt+Del) to restart the computer processing, but after pressing, it will return to this interface, which cannot solve the actual problem.

System reinstall failure can't boot repair method 1 Press the F8 key continuously, enter the system operation menu, select "Last Correct Configuration", restart the computer, see if it can be solved 2 Install the CD-ROM with the system, put it in the optical drive, restart the computer, enter the CD-ROM installation system state, and wait for the startup interface After flashing, don't choose the installation system.